Quick Finder -------------------------------------- ADF 20/8 UV AFP 35 AJ 4 Plus 55/50 AJ 4 Plus 100/36 AJ 4 Plus 100/57 AKP 5000 UV AMK basis module AMK 7000 UV-C ANC 2216-UV Clean Jet 1000 Plus Clean Jet 1000 Plus, suction hose DRAIN 4800/36 ESTAL 80/7 ESTAL 250/10 EXTREMA 300/10 Garten Jet 750 Garten Jet 1200 GP 3000 INOX GP 3000 INOX, suction hose GP 4500 INOX GP 4500 INOX, suction hose GP MAX HNB 1600 HWW 900/25 Plus HWW 1000/25 Plus HWW 1000/25 Plus F HWW 1000/25 Plus TLS HWW 1200/25 HWW 1300/25 Plus TLS HWW 1300/25 Plus TLS, prefilter HWW 3600 I HWW 3000 INOX HWW 4500 INOX HWW INOX 1000 Plus HWW INOX 1000 Plus TLS HWW INOX 1300 Plus F HWW INOX 1600 TLS HWW MAX T.I.P.-CONTROL Plus F INTEGRA 440 FS M 108-10 MAP 8000 UV-C Maxima 180 SX Maxima 250 SX Maxima 300 SX Maxima 400 SX MKF 1500 MultiOil 35 M PMA 7000 UVL PMA 12000 UVL Pond starter set II PSH 12000 UV-X PSH 20000 UV-X SCM 4 Plus 75/52 SCM 4 Plus 75/75 SCM 4 Plus 115/92 TKV 8000 TKX 8000 TKX 12000 TVX 8000 TVX 12000 TVX 12000, outlet hose TX 800 SR TX 2000 IL TX 3000 VR TX 5000 VR VARIO 1000 WDF 10000 WP 100-300 Plus WP 500-2 WP 500-10 R WP 1300 S WP 2500 S WP 5000 VX WP 8000 VX WP 10000 VX WP 12500 VX

Submersible pressure pumps - Informations

The fluid lifted in this way can be transported further under a high pressure and thus be used e.g. for an irrigation system or for domestic purposes. In addition, these pump are perfectly suited for direct irrigation out of wells, cisterns and reservoirs.

Deep-well pumps

Deep-well pumps draw water from very deep down

Deep-well pumps are specifically designed, extremely efficient submersible pressure pumps for narrow borehole wells of a min. diameter of 10 cm. In line with their intended use, the standard scope of delivery of these pumps includes a long connection cable and a suspension rope. Whereas the AJ Series units are mainly fit for the domestic range, the engineering features and the high performance of the units of the SCM Series will meet the highest demands in all areas of application.

Automation

Control system T.I.P.-MATIC

Automation of the operation of submersible pressure pumps and deep-well pumps is possible using our QUICK-MAT, Brio 2000-M or T.I.P.-MATIC control systems. With just very little effort the pumps can be used for automated water supply. This means the fluid conveyed is available as if it was taken from the water mains. And all this with a useful side effect: Some of the control systems will also protect the pumps from damage causes by dry-running since they will stop operation in the absence of water. For further information, please refer to the Automation chapter.

Installation of submersible pressure pumps and deep-well pumps

Installation

To suspend, position and secure these pumps from distortion inside cisterns or drilled wells and the like, please use only the suspension rope coming with the unit or other suitable stainless-steel or nylon cables. Also, make sure that the pump is at least 50 cm above ground. This will avoid swirling sand or other particles which may cause the pump to block or intensify the wearing action on the hydraulic components.

Some pumps of this type are subject to certain limits as to their max. depth of submersion in water. This max. submersion depth is indicated in the pumps' technical data.

Automation

While the pump is in operation, the suction chamber must always remain in the water, since otherwise overheating may cause damage. So when positioning the pump, please keep in mind that the water level may drop during operation owing to the changing seasons of the year, or even as a result the withdrawal process as such, or for other causes.

The standard scope of delivery of the units of the AJ and SCM series includes a check valve to prevent damage from pressure surges.

Copyright © 2008 T.I.P. Technische Industrie Produkte GmbH